| 经销商 | 联系方式 |
|---|---|
| 鑫浩悦科技 | 0755-85242024 |
本公司所生产设备为以下应用提供提供解决方案：如对噪声、传输距离及安全有限的场所、数据中心控制、信息分配、会议室演示以及教学环境和公司培训场所。
真诚服务是我们的理念，顾客满意是我们的宗旨。本公司将以最优惠的价格提供给客户最好的产品，并竭诚为客户提供优质的服务。
特点
l支持HDMI1.4a版本
l支持3D视频格式
l支持最高分辨率达1080P/60Hz
l支持最高速率1.65Gbps., TMDS时钟最高带宽为165Mhz
l支持8/10/12 位深色
l支持使用标准AWG26 线缆，输入传输距离达15米,输出传输距离达20米
l信号传输：用一条cat5或者cat6线（推荐使用）替代HDMI线，接收器和发射器之间线缆最长可达60米
l需要5V/1A的电源适配器
连接与操作：
1. 用一根HDMI线缆将信号源与延长器的发射端连接起来，线缆最长可达15米
2. 用一根HDMI线缆将显示端与延长器的接收端连接起来，线缆最长可达20米
3. 用一根cat5e线或者cat6线（推荐使用）来代替HDMI线将延长器的发射端和接收端连接起来，最长可传输60米
4. 将发射器和接收器连接上电源
5. LED指示灯说明：
TX端LED灯说明：当没有信号输入时，亮蓝色；当有信号输入时，亮红色。
RX端LED灯说明：当没有信号输入时，亮蓝色；当有信号输入时，亮红色。
6. EDID按键：该按键用来处理EDID，可以实现支持2D和3D的EDID的切换（开机默认的是支持3D的EDID）。
包裹附件:
1. TX发送器，RX接收器
2. 5V 电源适配器
3.用户手册
注意事项:
请正确使用并妥善保养，以保证产品性能以及正常工作。
1. 要远离潮湿、高温、多尘、腐蚀性及氧化性气体环境以免损坏。
2. 所有部件应避免强烈振动，不得碰撞、敲击、跌摔，以免损坏。
3. 请勿用湿手接触本机电源适配器插头
4. 从电源插座上拔掉适配器插头时,请握住插头,不要拉电源线.
5. 机器不用时请关掉电源(长期不用时请拔掉电源适配器插头)
6. 请勿开启机盖,切勿接触机内任何器件.
7. 必须使用厂家提供或经厂家认可的电源适配器
在通电前，应仔细检查连接线是否正常，必须在保证所有接口为正常连接。常见故障判断及处理方法如下：
|
序号 |
故障现象 |
原因及解决方法 |
|
1 |
不通电 |
1、检查电源插头是否正确插入电源插座. 2、检查电源是否打开. |
|
2 |
无图像 |
1、确认电视已开机并处于与本机连接. 2、输入信号源是否开启并连接完好. 3、检查系统的连接状态. 4、检查连接线是否完好. 5、线材质量（HDMI线材要求符合HDMI 标准）. |
|
3 |
图像模糊 |
1、连接口重新连接,以防插座接口接触不良 2、线材质量（HDMI线材要求符合HDMI 标准） |
 |
|
|
|
产品规格:
接收器与发射端之间的CAT5e或者CAT6线缆…..……..........………….……………..可达60米
HDMI 输入…..…………………...……………24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
支持音频格式输入.…………………………………DTS-HD/Dolby-trueHD/DTS/Dolby-AC3/DSD
HDMI 输出…..…………….…...……………24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
支持音频格式输出...……. ………………………… DTS-HD/Dolby-trueHD/DTS/Dolby-AC3/DSD
最大传输带宽……………………………………………………………………………………165MHz
最大传输速率……………….…….………………….………….……………………………1.65Gbps
输入视频信号………….…………………………..………………………….…… 0.5~1.5Volts p-p
输出DDC 信号……………………………………………...……………………… 5Volts p-p (TTL)
输入HDMI线缆长度………….……………. ….....………...≤15m AWG26 标准HDMI规格的线缆
输出HDMI线缆长度………….……………. ….....………...≤20m AWG26 标准HDMI规格的线缆
最大工作电流TX…………………………………….....………………………………………...510mA
最大工作电流RX………………………………………....……………………………………...100mA
电源适配器规格………...………….........…交流输入(50HZ, 60HZ) 100V-240V; 直流输出5V/1A
工作温度范围……..…………….……………………........……………….…………… (-15 to +55℃)
工作湿度范围………………………….………. ……..…....……….…. ………5 to 90%RH (无冷凝)
尺寸(长x 宽x 高) ………………………………......…………………………81x43x22 (mm)
TX重量.……………………………………………………........…..………………………………100g
RX重量..………………………………………………….......……..………………………………120g
U S E R M A N U A L
60m HDMI Extender over single cat 5E/6
Enjoy the vivid world!
INTRODUCTION
Dear customer
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
The Extender uses single cat-5E or cat-6(recommended) cables instead of HDMI cable to transmit high definition signalup to 60 meters, cutting down the cost. The Extender is designed to supply for long distance transmission of high definition signal.
Our devices offer solutions for noise, space and security concerns, data center control, information distribution, conference room presentation, school and corporate training environments.
FEATURES
lSupport HDMI 1.4a
lSupport 3D
lSupport highest video resolution 1080p/60Hz
lSupport 1.65Gbps data rate and tmds clock up to 165MHz
lSupport 8/10/12 bit deep color
lSupport AWG26 HDMI standard cable, input up to 15 metres, output up to 20 metres
lSignal transmission: By using single cat-5e or cat-6(recommended) cable instead of HDMI cable, it can extend the distance up to 60metersbetween TX and RX.
lNo loss of quality
lInstall in minutes
lNeed DC5V/1A power supply
Product Picture:
Physical Connection Showing Picture：
Operating and Connecting：
1. Connect one HDMI cablebetween source device and TX Extender, the max cable distance is15 meters
2. Connect one HDMI cable between display device and RX Extender, the max cable distance is 20 meters
3. Connect single cat-5e or cat-6(recommended) cables instead of HDMI cables between TX and RX Extender, the max cable distance is 60 meters
4. Connect 5V power supply to the TX and RX.
5. LED indicator light
TX LED indicator light: When there is no signal input, it turns blue; When there is signal input, it turns red.
RX LED indicator light: When there is no signal input, it turns blue; When there is signal input, it turns red.
6. EDID button: The button can support the switch of EDID between 2D and 3D.(3D is the default EDID when the power is on).
SPECIFICATIONS:
Length of CAT-6/CAT-5E cable between Rx and TX…………….............…..Up to 60meters
HDMI Input…..…………………...………24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
Support audio input..……............................…DTS-HD/Dolby-trueHD/DTS/Dolby-AC3/DSD
HDMI Output…..…………….…...………24/50/60fs/1080p/1080i/720p/576p/576i/480p/480i
Support audio output...……. ……………….…DTS-HD/Dolby-trueHD/DTS/Dolby-AC3/DSD
Max bandwidth……………………………………………………………………………165MHz
Max baud rate……………….…….………………….………….………………………1.65Gbps
Input videosignal ………….…………………………..…………………….… 0.5~1.5Volts p-p
Output DDC signal ……………………………………………………………… 5Volts p-p (TT1L)
Input HDMI cable distance………….…………............…..≤15m AWG26 HDMI standard cable
Output HDMI cable distance............................................ ≤20m AWG26 HDMI standard cable
TX Max working current………………………………………...………….………………...510mA
RX Max working current…………………………………………...………………………...100mA
Power adapter format………...………Input:AC (50HZ, 60HZ) 100V-240V; Output: DC5V/1A
Operating Temperature range……..…………….………………………………… (-15 to +55℃)
Operating Humidity range………………………….….……….5 to 90%RH (No Condensation)
Dimension (L x W x H) ……………………………….…………………………81x43x22 (mm)
TX Weight…..……………………………………………..………………………........………100g
RX Weight........................................................................................................................120g
The Package includes:
1.TX Extender :1pc RX Extender:1 pc
2.5V DC Power adapter
3. User Manual
Notes:
Pls use the machine as the instruction listed to keep the long use lifetime of the machine.
1. The machine should be placed at the spot far from the Damp, High-Temperature, Dusty, Erosive, and oxidative environment.
2. All parts will be free from the strong shake, hit, fall.
3. Touching the power adaptor with the wet hands is prohibited.
4. Pls hold the power adaptor head and do not pull the power cord when cut off from the socket.
5. Pls turn the power off when the machine is not used for long time.
6. Pls do not open the cover and do not touch the inside parts.
7. Pls use the original factory power adaptor.
Before power on, pls check the connection line carefully. And make sure that all interfaces are normally connected. The common trouble shooting way shows below:
|
Serial NO |
Trouble Description |
Cause and Ways to deal with |
|
1 |
Non-Power-Connected |
1、Check if the power adaptor head is truly and correctly inserted the power socket. 2、Check the power switch if it is in on status. |
|
2 |
No Picture |
1、Pls to make sure that the TV is on and has been connected with the machine. 2、To check if the signal source is on and well connected. 3、Check the system connection quality. 4、Check if the line is all good quality. 5、Check the cable quality |
|
3 |
Obscure Picture |
1、To try again to connect the cable to be free from the unsuccessful connection. 2、HDMI Cable Quality( HDMI Standard cable) |
 |
|
|
|
首页