返回
爱思创电子(上海)有限公司_爱思创Extron中国
双绞线矩阵切换器-MTPX Plus 1632图片
双绞线矩阵切换器-MTPX Plus 1632
厂家报价:价格面议
生产状态:在产
爱思创Extron电子
爱思创Extron电子
爱思创电子(上海)有限公司(爱思创Extron中国)全球总部位于美国加州,是世界领先的专业视音频系统集成产品的生产商。爱思创Extron产品主要包括视音频控制系统、计算机视频接口、切换器、矩阵切换器、...
经销商 联系方式
爱思创Extron电子 4000.398766、 021-3760 1568
  • 产品
  • 参数
  • 附件配件
  • 下载

  Extron MTPX Plus 系列双绞线矩阵切换器是新一代双绞线集成的出色代表.

  本地视频及音频的输入和输出,使得与 MTPX Plus 矩阵处于相同机架内的设备可以与其直接连接。这样就无需使用附加的 MTP 发送器和接收器,从而大大降低了系统的复杂性。 MTPX Plus 系列还在其所有输入和输出上都提供了动态扭曲延时均衡调整功能。无论选择输入/输出电缆长度的哪种组合,这一行业创新技术都可确保消除 UTP 电缆的扭曲现象。另一项创新特性是本地 RS-232 插入端口,它允许位于 MTPX Plus 旁边的控制系统通过用于传输视音频信号的相同的 UTP 输出电缆,连接并控制远程显示设备。

  在与 Extron MTP U 系列通用型微型双绞线接收器配合使用时,MTPX 系列双绞线矩阵切换器允许通过单根 CAT 5电缆发送带有音频或 RS-232 控制信号的复合视频、S-视频和 VGA 信号,并输出在显示设备合适的连接器上。通过将一根电缆用于所有信号类型,可以简化系统布线,并且在每台显示设备上仅使用一个矩阵切换器的输出和一台 MTP U 系列接收器。

  其它特性还包括可在多路输出上切换峰值预调整功能以便长距离传输信号、可进行音频输入增益和衰减以平衡音频电平、可对本地输出进行输出音量控制,以及 IP Link 以太网连接。与传统的双绞线矩阵切换器相比,MTPX Plus 系列双绞线矩阵切换器的强大特性可以使集成商大大缩短安装时间,并且降低与机架空间、布线和安装相关的各类成本。

特性

·动态扭曲延时补偿

·本地 RS-232 插入端口

·视频电平和峰值补偿

·可在 50% 的输出上进行视频峰值预调整

·本地视频输入和输出

·本地音频输入和输出

·音频输入增益/衰减调整

·本地音频输出音量控制

·IP Link 以太网连接

·增强型 QS-FPC™ - 快速切换前面板控制器

·RS-232/RS-422 切换器控制端口

·与 Extron MTP 系列产品相兼容,包括 MTP U系列通用型双绞线接收器

示意图

面板图

MTPX Plus Series
 
Video
   Routing   
      MTPX Plus 816  8 x 16 matrix, 3 x 1 local
      MTPX Plus 168  16 x 8 matrix, 3 x 1 local
      MTPX Plus 1616  16 x 16 matrix, 3 x 1 local
      MTPX Plus 1632  16 x 32 matrix, 6 x 2 local
      MTPX Plus 3216  32 x 16 matrix, 6 x 2 local
      MTPX Plus 3232  32 x 32 matrix, 6 x 2 local
   Gain  Unity
   Crosstalk   
      816, 168, 1616 models  -80 dB @ 1 MHz, -71 dB @ 5 MHz, -55 dB @ 10 MHz, -45 dB @ 30 MHz, -37 dB @ 100 MHz
      1632, 3216, 3232 models  -90 dB @ 1 MHz, -76 @ 5 MHz, -72 dB @ 10 MHz, -60 dB @ 30 MHz, -50dB @ 100 MHz
   Switching speed  200 ms (max.)
 
Video input — local
   Number/signal type  3 or 6 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level), S-video, composite video
   Connectors  3 or 6 female 15-pin HD
   Nominal level  0.7 Vp-p for RGB
   Minimum/maximum levels  0.3 V to 1.45 Vp-p with no offset at unity gain
   Impedance  75 ohms
   Horizontal frequency  15 kHz to 130 kHz
   Vertical frequency  30 Hz to 150 Hz
   Return loss  <-30 dB @ 5 MHz
   DC offset (max. allowable)  250 mV
 
Video input — main (see transmitters' output specifications)
   Number/signal type  8, 16, or 32 proprietary analog signals
   Connectors  8, 16, or 32 (depending on configuration) female RJ-45 connectors
 
Video output — local
   Number/signal type  1 or 2 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level sync),
S-video, composite video
   Connectors  1 or 2 female 15-pin HD
   Nominal level  0.7 Vp-p for RGB
   Impedance  75 ohms
   Return loss  <-30 dB @ 5 MHz
   DC offset  <±20 mV with input at 0 offset
 
Video output — main (see receivers' input specifications)
   Number/signal type  8, 16, or 32 proprietary analog signals
   Connectors  8, 16, or 32 (depending on configuration) female RJ-45 connectors
 
Sync — local inputs and outputs only
   Input type  RGBHV, RGBS, RGsB, RsGsBs
   Output type  See receiver specifications (see specifications on Web site).
   Input level  3.5 V to 5.5 Vp-p, unterminated; 4.0 V to 5.0 Vp-p normal
   Output level  See receiver specifications (see specifications on Web site).
   Input impedance  573 ohms ± 5%
   Output impedance  110 ohms
   Max. input voltage  5.0 Vp-p
   Max. rise/fall time  4 ns
   Polarity  Positive or negative
 
Audio
   Routing   
      MTPX Plus 816  8 x 16 mono matrix, 3 x 4 local
      MTPX Plus 168  16 x 8 mono matrix, 3 x 4 local
      MTPX Plus 1616  16 x 16 mono matrix, 3 x 4 local
      MTPX Plus 1632  16 x 32 mono matrix, 6 x 8 local
      MTPX Plus 3216  32 x 16 mono matrix, 6 x 8 local
      MTPX Plus 3232  32 x 32 mono matrix, 6 x 8 local
   Gain (local inputs and outputs)  Unbalanced output: 0 dB; balanced output: +6 dB
   Frequency response  20 Hz to 20 kHz, ±1 dB
   THD + Noise  0.15% @ 1 kHz at nominal level
   S/N  >70 dB at maximum output (unweighted)
   CMRR  >43 dB @ 20 Hz to 20 kHz
 
Audio input — local
   Number/signal type  3 or 6 stereo, balanced/unbalanced
   Connectors  (3) or (6) 3.5 mm captive screw connectors, 5 pole
   Impedance  >10k ohms unbalanced
   Nominal level  +4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
   Maximum level  +18 dBu, (unbalanced) at 1% THD+N
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
 
Audio input — main (see transmitters' output specifications)
   Number/signal type  8, 16, or 32 proprietary analog signals
   Connectors  8, 16, or 32 (depending on configuration) female RJ-45 connectors
 
Audio output — local
   Number/signal type  4 or 8 dual mono, balanced/unbalanced
   Connectors  (4) or (8) 3.5 mm captive screw connectors, 5 pole
   Impedance  50 ohms unbalanced, 100 ohms balanced
   Gain error  ±1 dB channel to channel
   Maximum level (Hi-Z)  +18 dBu, balanced or unbalanced at 1% THD+N
   Maximum level (600 ohm)  +15 dBm, balanced or unbalanced at 1% THD+N
 
Audio output — main (see receivers' input specifications)
   Number/signal type  8, 16, or 32 proprietary analog signals
   Connectors  8, 16, or 32 (depending on configuration) female RJ-45 connectors
 
Control/remote — switcher host control
   Serial host control ports  1 RS-232 or RS-422, rear panel 9-pin female D connector
1 RS-232 front panel 2.5 mm mini stereo jack
   Baud rate and protocol  9600 baud (default), 19200, 38400, and 115200 (adjustable); 8 data bits; 1 stop bit; no parity
   Serial control pin configurations
      9-pin female D connector  RS-232: 2 = Tx, 3 = Rx, 5 = GND
RS-422: 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
      Mini stereo jack  Tip = TX, ring = RX, sleeve = GND
   Ethernet control port  1 RJ-45 female connector
   Ethernet data rate  10/100Base-T, half/full duplex with autodetect
   Ethernet protocol  ARP, DHCP, ICMP (ping), TCP/IP, UDP, Telnet, HTTP, SMTP
   Default settings  Link speed and duplex level = autodetected
IP address = 192.168.254.254, Subnet mask = 255.255.0.0, Gateway = 0.0.0.0,
DHCP = off
   Web server  Up to 200 simultaneous sessions
16 MB nonvolatile user memory
   Program control  Extron's control/configuration program for Windows®
Extron's Simple Instruction Set (SIS™)
Microsoft® Internet Explorer version 6 or higher, Telnet
 
Control/remote — external device (pass-through, unidirectional, or bidirectional)
   Serial control ports  RS-232, 3.5 mm captive screw connectors, 3 pole
      3232 and 1632 models  16 connectors
      3216, 1616, and 816 models  8 connectors
      168 models  4 connectors
   Baud rate and protocol  Up to 38400 baud, 9600 baud (default); 5-8 data bits; 1 or 2 stop bits; odd, even, or no parity;
XON, XOFF, or no flow control
    NOTE     Protocol is mirrored between the switcher and the receiver.
   Serial control pin configurations  1 = Tx, 2 = Rx, 3 = GND
 
General
   Recommended cable type  CAT 5/5E/6/7 (shielded or unshielded)
   Power  100 VAC to 240 VAC, 50-60 Hz, internal
      1632, 3216, 3232 models  220 watts
      816, 168, 1616 models  120 watts
   Temperature/humidity  Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling  Fan, left to right (as viewed from the front panel)
   Rack mount  Yes
   Enclosure type  Metal
   Enclosure dimensions   
      1632, 3216, 3232 models  5.25" H x 17.0" W x 9.4" D (3U high, full rack wide)
(13.3 cm H x 43.1 cm W x 23.9 cm D)
(Depth excludes connectors. Width excludes rack ears.)
      816, 168, 1616 models  3.5" H x 17.0" W x 9.4" D (2U high, full rack wide)
(8.9 cm H x 43.1 cm W x 23.9 cm D)
(Depth excludes connectors. Width excludes rack ears.)
   Product weight   
      1632, 3216, 3232 models  16 lbs (7.3 kg)
      816, 168, 1616 models  8.5 lbs (3.9 kg)
   Shipping weight   
      1632, 3216, 3232 models  26 lbs (ll.8 kg)
      816, 168, 1616 models  18 lbs (9 kg)
   DIM weight (International)   
      1632, 3216, 3232 models  26 lbs (11.8 kg)
      816, 168, 1616 models  18 lbs (9 kg)
   Vibration  ISTA 1A in carton (International Safe Transit Association)
   Regulatory compliance
      Safety  CE, CUL, UL
      EMI/EMC  CE, C-tick, FCC Class A, ICES, VCCI
      Environmental  Complies with the appropriate requirements of WEEE.
   MTBF  30,000 hours
   Warranty  3 years parts and labor
    NOTE     All nominal levels are at ±10%.
    NOTE     Specifications are subject to change without notice.
暂无相关附件!!!
暂无相关下载!!!